20 Gauge Wide Crown Stapler

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

Worked great out of the box. Oiled it up, loaded it, fired a few test rounds to adjust pressure and went to work. Some 2000 staples later it had only missed a few times when feeding broken rows of staples.

USed it to install several hundred feet of hardware cloth to 2 bys. Never broke a wire when adjusted properly. VVery pleased thus far. NOTE: I used CLP to oil this and it worked very well

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

Bought this for stapling insulation in the ceiling. Makes the job a lot easier than using a manual stapler. I'm using Arrow T50 staples.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

After years of frustration using electric staplers I decided to try this one. I've gone through 2,000 T-50 staples without a jam. Unit is easy to load and every staple goes in to the required depth with the need to use a hammer.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

Another HF gem!!! I had a Arrow Lithium-Ion battery powered kit which I paid about 1 benny for, and I will soon auction that off since this is so much better. It drives my arrow T50 without any issues, I can adjust how much and deep to drive them. while I have yet to try it, I think it will shoot other staples like the crowned top ones for wires. It uses very little air, so on a 6 gallon compressor, you can go forever.

It is easy enough to clear a jam, but I have yet to have one. The magazine slides back and you can pull any stuck staples out with your pinky if needed. I have also yet to have any double shoots. I did put the oil in before I started, like the instructions said to.

I feel bad for all those who paid more for a Bostich, as this is just as good at a fraction of the price. I am going to use this next to re-cover an amp with new tolex.

Enjoy!

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

Bought this when it was on sale. Its quite well built. Remember to regulate your air pressure to set depth. Mine worked best at 70-80 psi. Loading and unloading staples is easy. Rarely the last staple in the clip will jam. Its very easy to clear though. Remember to oil prior to use with 8-10 drops of oil and every hour of use add 7-8 drops. This will prevent any erratic behavior. Use only Arrow T-50 or Stanley sharp shooter staples. Using off brand staples causes issues. Use higher pressure for longer staples. I have not used my manual stapler since I bought this 2 years ago. Recommended.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

I purchased after fighting an electric stapler for a couple days on a boat upholstery project.
the electric would barely set the soft stainless (Monel)T-50 staples in hard plastic and not at all into fiberglass.
the powerful air stapler drove them with ease into hard material :)

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

This stapler is very powerful compared to other staplers.You will have to reduce air pressure and use longer staples depending on material. T50 arrow staples are available everywhere.This stapler can't be beat. Don't waste your time with other staplers, absolutley the best.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

add two drops of oil, t-50 staples and air supply...start shooting staples.
tried a hand stapler first...wouldn't penetrate plastic seat pan. ran to HF bought their air stapler and finished my project in minutes.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

I bought this stapler to use upholstering boat seats. I've used it for everything. Never jams, very powerful. Uses readily available T-50 staples from Arrow, Stanley, etc. The only downside is dragging an air hose around but that's not the stapler's fault. Hands down the best stapler I've ever owned. Highly recommend it.

Comments about Central Pneumatic 20 Gauge Wide Crown Stapler:

Put all the wire on my rabbit hutch with this gun...works amazing...saved so much time...use T-50 nails